Eterinox – Single-wall oval section flue system

Eterinox - Serie ovale

Eterinox – Oval series

Technical Data

		Material specification Internal diameter (mm): 130 (150×100) • 150 (170×120) • 180 (200×150) • 200 (230×150) • 250 (295×180) • 300 (355×210) • 350 (395×280) • 400 (500×300)
Inner wall	Nominal thickness: 0.5 mm Grade 1.4404 (AISI 316L stainless steel)
	Wall thermal resistance m²K/W at 200°C: Without insulation = 0.00
Joints	The product requires a locking band. In order not to downgrade the product, if sealants are used, it is recommended to use those with a temperature rating above 1000°C.
	Roughness: average value 1 mm

General information
Installation	Internal: Yes External: No, not resistant to rainwater penetration
	Fields of application Ducts and flues connected to forced-air boilers, atmospheric boilers, type B appliances, fireplaces, stoves, kitchen hoods, ovens, and ventilation ducts.
	Permitted fuels T600 gas, diesel oil, LPG, pellets, and wood.
	Storage: In environments where the atmosphere is non-corrosive
	Product warranty: In accordance with Directive 99/44/EC
	Hazardous substances: None
	Freeze–thaw resistance: Compliant with UNI EN 1856-1
	Accidental contact: Protective shielding is required when the wall surface temperature exceeds 70°C
	Storage: Do not store the material near ferrous materials; environments must be dry and protected from weather exposure
	Limitations of use: The use of stainless steel flue systems is not recommended in environments such as laundries, dry cleaners, furriers, printing facilities, beauty salons, or in any areas where halogenated or chromated vapors are present

Features

	Product designation according to EN 1856-2 standard Duct.
	Standard number EN 1856-2
	Temperature rating T600
	Pressure rating N1
	Condensate resistance D
	Corrosion resistance V2
	Internal wall thickness L50050
	Fire resistance from inside and distance to combustible materials G

Performance requirements according to the designation
		Temperature rating T600 – operation with nominal flue gas temperature below 600°C
	Pressure rating N1	Operation with positive and negative pressure up to 40 Pa. Permissible leakage less than 2.0 l/s·m²
		Condensate resistance D – operation with dry flue gases
		Corrosion resistance V2 – suitable for operation with gas, diesel oil, LPG, pellets, and wood.
		Internal wall specification L501.4404 (Stainless steel AISI 316L)
		Internal wall thickness 050 – nominal thickness 0.5 mm
		Fire resistance from inside: G Resistant to internal fire
		Distance to combustible materials – To be installed inside a technical shaft, masonry chimney.

Installation

INSTALLATION INSTRUCTIONS

Position the components as indicated by the arrow stamped on the label and shown on the piece.
For T600_N1_D use, the product must be installed without the use of silicone or sealants.
After connecting the components, fit and tighten the appropriate locking clamp at each joint.
Avoid the accumulation of condensate or soot, which may cause corrosion. Also avoid horizontal sections and, in any case, install the elements with the longitudinal weld facing upwards (3% slope).

ESSENTIAL CHARACTERISTICS

Wind load resistance:

Distance between wall brackets: NPD m
Free length from the last bracket: NPD m

Compression resistance:

Maximum load for linear elements: NPD (No Performance Determined)
Maximum load for 90° straight fitting: NPD (No Performance Determined)
Maximum load for wall-mounted chimney support: NPD (No Performance Determined)

Tensile and bending resistance (straight elements):

Maximum tensile load (connection means of chimney elements and fittings): NPD (No Performance Determined)
Non-vertical installations: max. 90°
Non-vertical installations: distance between wall chimney supports = NPD (No Performance Determined)

Tensile and bending resistance (non-linear elements):

Non-vertical installations: NPD

FLUE SYSTEM MAINTENANCE

Scheduled maintenance carried out by qualified personnel:

Unless otherwise required by regulations or agreed with users, the following maintenance intervals are recommended:
- Gaseous fuels: once per year;
- Liquid fuels: once every 6 months;
- Solid fuels: once per month.
Cleaning using a soft plastic brush or sponge of the flue pipe, the technical compartment for air supply and ventilation of the ducts, the inspection connection, the chimney cap; checking the free flow of flue gases and condensate, etc.

Documentation

Ovale dichiarazione di prestazione

1 file(s) 492.09 KB

Download

Ovale catalogo tecnico

1 file(s) 2.12 MB

Download

Request information or a customized quote

"*" indicates required fields

Dati personali*

First Last

Email*

Telefono*

Ragione Sociale

Sito Web

Nazione*

CAP*

Città*

Provincia*

Indirizzo*

Messaggio*